Bilston grew up as a Black Country market town and the wiring still tells that story. The long terraces off the centre and the interwar council-built streets around Bradley and Ettingshall were wired for a house with a radio and a cooker, not an induction hob, an electric shower and a car on charge. Rewirable fuse boards, borrowed neutrals picked up during a 1980s extension and pre-1990s cable are exactly the sort of thing an inspection here turns up. The newer infill dropped between the older streets usually tests cleanly, though the bonding is often the part nobody finished.
An Electrical Installation Condition Report is a measured test, not a look round. Every final circuit, the consumer unit, the earthing arrangement, the main protective bonding and a working sample of sockets, switches and light fittings are examined and recorded. Each defect is given a code — C1 where danger is present, C2 where it is potentially dangerous, C3 where an improvement is worth making, FI where nothing can be concluded without further investigation. The installation then carries one verdict, Satisfactory or Unsatisfactory, and that is the line an agent, insurer, lender or buyer’s solicitor reads first.
Adam carries out the testing and writes the report himself, so what was found and what you are told are the same thing. Nothing gets inflated to sell a rewire. For the wider picture read our EICR service page, or see what else we handle as an electrician in Bilston. Shops, units and offices sit under commercial electrical work, the same testing runs over in Walsall, and you can ask for a free quote at any point.
Nothing judged at a glance: boards opened, circuits measured, findings coded and then explained.
The board comes off and every way is identified and traced back to what it feeds. We are looking for scorched terminations, three manufacturers’ parts crammed into one enclosure, circuits nobody has labelled in forty years, and rewirable fuse carriers still doing a job they were never meant to keep doing.
The main earth and the protective bonding runs to the incoming gas and water services and to any structural steel are traced back and proved. In Bilston’s older terraces this is the most common thing we write up — bonding never fitted at all, cut too small, or left disconnected after a kitchen or bathroom was ripped out.
Accessories come off the wall as a proper sample: polarity, terminal condition, heat damage, and the DIY spur someone added to feed a shed, a garage or a converted attic room all get looked at rather than assumed.
Trip times are measured on a tester, not judged by pressing the test button. Where a Bilston board is old enough to carry no RCD protection at all, we say so plainly and set out which circuits that leaves exposed and why it matters.
You get the complete report, every observation coded, and one clear outcome. It is the document your tenant, agent, insurer or buyer will ask to see. We go through it with you on the phone rather than firing over a PDF and going quiet.
Four stages: message us, pick a slot, we test, the certificate follows.
Ring, WhatsApp or run the estimator. The age of the property and roughly how many circuits it has is enough for a price — no visit needed to quote.
We fit the appointment around tenants, opening hours, or whatever date a sale or a licence renewal has put on you.
Circuits are isolated in turn, inspected and tested, and the power goes back on as soon as each stage allows.
The coded report follows, along with a call explaining anything sitting at C1, C2 or FI before you decide a thing.
Need something other than an inspection in Bilston? The same electrician covers the rest, and the neighbouring towns get the same EICR service.
What Bilston landlords, homeowners and business owners ask before booking.
Price follows the number of circuits and consumer units, not the postcode. A one-bed flat on a single board is a short job; a terrace with an extension, a garage supply and two boards is not. Tell us about the property and you get a fixed figure before we start, with nothing bolted on afterwards. Ask for a free quote.
If the home is privately rented in England, yes. The Electrical Safety Standards in the Private Rented Sector (England) Regulations require a valid report at intervals of no more than five years, a copy for the tenant, and a copy for the local authority if they ask. That applies in WV14 exactly as it does anywhere else in England.
Two to four hours covers most Bilston homes. Larger properties, a second board or a commercial unit will take longer. You get a realistic time window before the appointment, because power comes off a circuit at a time while we test.
C1 is danger present and needs dealing with straight away. C2 is potentially dangerous and has to be put right before the report can pass. C3 is a recommendation and fails nothing. FI means further investigation is needed before a judgement can be made. One C1 or C2 anywhere makes the whole result Unsatisfactory.
All of WV14 — the town centre and market, Bradley, Ettingshall and the streets running out towards Moxley and Darlaston. Our base is in Wolverhampton, roughly ten minutes away, so a same-day response is usually realistic.
No, and we will not pretend otherwise. The coded report belongs to you regardless of who ends up doing the repairs. Should you want us to price them, we cost only the items the codes demand and keep anything discretionary on its own line so you can see the difference.
Real reviews from customers across Wolverhampton & the West Midlands. You deal directly with Adam, every time.
Adam visited our property to carry out the EICR inspection. He was very friendly, professional, and punctual. Overall, it was a very smooth and positive experience. I would definitely recommend Adam to anyone looking for a reliable and professional electrician.
Adam carried out an EICR on our property and I was really impressed with his service. Communication was excellent from start to finish, he was transparent with pricing, and provided a clear breakdown of any issues.
Very professional and friendly.
Messaged Adam to get new light fixtures installed in my kitchen. He was able to get this sorted for me within 2 days of messaging him. Quick to respond and efficient at getting the job done.
Adam was very professional, friendly, knowledgeable and polite. Changed the old fuse box to a brand new one. I would recommend his service to anyone — definitely will be using him again for any future work.
I had a partial power outage. Adam came over very quickly and sorted out the problem. No further costs beyond the call-out charge, which was explained when I called. Very pleasant, courteous and professional. Will not hesitate to use again.
Emergency call-out due to an alarm fault. Adam was great, very friendly and helpful. Took his details so I can use him directly next time.
Excellent! Had a bathroom fan and several sockets channelled and fitted. Adam explained everything and answered all of our questions to make sure we got the fittings that suited our needs. Worked late into a Sunday evening to get the job finished, and even tidied as he went along. Would recommend!
Needed some electric in my shed and Adam helped me sort this out swiftly and very professionally too. Super happy with my service and he cleaned up afterwards too, so that was a plus!
He was very prompt in fitting me in. Polite and helpful, and the price was cheaper than expected. Definitely recommended.
Amazing service — helped me with an electrical issue during the evening. Friendly service and fixed the issue quickly. I would definitely recommend to all my friends and family.
Excellent job, very knowledgeable and high standard of quality. Would recommend to anyone requiring electrical work!
Bilston is an old market town that got absorbed into Wolverhampton without losing its own character, and the housing runs the same way: tight Victorian terraces near the centre, interwar council-built streets around Bradley and Ettingshall, and pockets of new build squeezed in between. Each of those ages of wiring fails differently, which is why we test instead of assuming. Wherever you are in WV14, the process does not change — every circuit measured, every finding coded.
A free, no-obligation price for a Bilston EICR — rented, owner-occupied or commercial premises.
All work is completed by qualified and certified electricians, with relevant approvals and documentation provided where required.
